Side power anchor windlass jammed with anchor rope
取得連結
Facebook
X
Pinterest
以電子郵件傳送
其他應用程式
This windlass is installed on a axopar 37 Cabin.
There was problem since the installation, boat owner even lost an anchor, I'm not sure why...
Went for inspection on 2018/10/08, the rope is jammed on the disk.
rope turns a full round, and jammed the windlass
the other angle
It seems the problem is the spacing between the deflector(black one) and the inner disk(on the right)
You have to unmount the outer disk, then release the jammed rope.
we first installed the rope guide, which was missing during last installation.
try again, it jammed again.
The cause is still the same, too much space between deflector and inner disk.
The deflector is not at center of 2 disks.
it's really off centered
This is how it stated in the manual.
It seems that the bracket is not fitting to the left... We have adjust the bracket and get it to the most left position.
We have adjust the rope guide bracket, but only get couple mm of improvement. In my point of view it still off centered.
we also adjust the angle, then test seems be ok.
We have tested with boat owner, also with remote control. it seems fine, after we left, boat owner go for sea trial, then it jammed again.
I believe the cause is the same, but I have put the bracket close to inner disk as possible, no more space to adjust the deflector position.
Not sure if the size of deflector is correct or not,the spacing shown on the manual seems impossible for the set we have on boat.
NMEA2000 is the protocol used in boat, it based on can bus, but with definition on different PGN(group nr)...etc. The best one I found for arduino is this one: https://github.com/ttlappalainen He has both NMEA 0183 and nmea 2000 libraries. To start with NMEA2000 library for arduino like boards, this library reference should be read: https://github.com/ttlappalainen/NMEA2000/blob/master/Documents/NMEA2000_library_reference.pdf There are few boards comes with can bus controller, but will need external can bus phy, such as Due, and esp32. For some boards, you will need external can bus controller(MCP2515) and can bus transiever(MCP2551) So the NMEA2000 libraries need different extra lib to make it works on different board, detail info in the read me of the lib: https://github.com/ttlappalainen/NMEA2000/blob/master/README.adoc To start, I purchased a seeeduino can bus shield: it has an MCP2515 CAN Bus controller with SPI interface and MCP2551 CA...
雖然我是鋰鐵電池的愛好者,但是這價格很高,懂得設計的人很少, 所以在船上也很少看到..... 我希望記下我目前對鉛酸電池的知識....這些都是google的到的東西,只是鉛酸電池發展非常久,種類分支非常多,不容易一次都找到.... 船上的鉛酸電池, 一般的船主會看見電壓, 當你跟船主說這電池可能要換了, 它們常常會說我看電壓還很好啊! 眼神會透漏著"你們公司又來巧立名目了...."真是冤望啊~~ 以前鉛酸電池的檢測很困難, 這幾年電子儀器的進步,你可以在網路上花個1000~3000NTD買個鉛蓄電池的檢測器,這個東西會告訴你一般產業裡對鉛酸電池的體檢標準.... 有時電池的電壓會維持得不錯,但是完全不具儲電及放電能力... 主要須注意電池的: 1.電壓(無充放電下): 這就不用說了, 掉到12V以下的電池通常是被惡劣對待過了(不適當的充放電) 2.電池內阻:電池的內部電阻, 內阻會隨著使用慢慢變大, 當然,內阻越大就越差了....但是內阻的值則依電池的類型會也些不同 3. CCA: cold crank amp: 這是測試電池啟動的能力,規範上還有CA, CCA是-18度C, CA是在0度C,時測試: " and measure the discharge load in amperes that a new, fully-charged battery can deliver for 30 seconds, while still maintaining terminal voltage equal to or higher than 1.20 volts per cell. " 因為包含了電壓的維持能力跟電流的釋放能力所以常被拿來,當作電池健康狀況的指標,一般車廠說的電池剩下多少%壽命/健康,就是以這個量到的值除以電池上標示的額定CCA.所以在做CCA測試前必須先知道電池上標示的額定CCA,這樣百分比才有意義... 下圖示網路上可以找到的測試器.... 電池的種類: 當需要更換電池時,換哪種電池好,就又是一大問題...(這時就又會有"你們怎麼那麼貴"的問題....) 鉛酸電池的發展歷史很長,變成現在的電池"名目"很多,眾多的名目跟眾多的...
留言
張貼留言